PIC18C452T-E/L【PDF 51/279 页】IC MCU OTP 16KX16 A/D 44PLCC

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3889

47页 48页 49页 50页 [51页]52页 53页 54页 55页

PIC18CXX2

DS39026C-page 142

2001 Microchip Technology Inc.

14.4.10

ACKNOWLEDGE SEQUENCE

TIMING

An Acknowledge sequence is enabled by setting the

Acknowledge

sequence

enable

bit,

ACKEN

(SSPCON2<4>). When this bit is set, the SCL pin is

pulled low and the contents of the Acknowledge data bit

is presented on the SDA pin. If the user wishes to gen-

erate an Acknowledge, then the ACKDT bit should be

cleared. If not, the user should set the ACKDT bit before

starting an Acknowledge sequence. The baud rate gen-

erator then counts for one rollover period (TBRG) and the

SCL pin is de-asserted (pulled high). When the SCL pin

is sampled high (clock arbitration), the baud rate gener-

ator counts for TBRG. The SCL pin is then pulled low. Fol-

lowing this, the ACKEN bit is automatically cleared, the

baud rate generator is turned off and the MSSP module

then goes into IDLE mode (Figure 14-20).

14.4.10.1

WCOL Status Flag

If the user writes the SSPBUF when an Acknowledge

sequence is in progress, then WCOL is set and the

contents of the buffer are unchanged (the write doesn’t

occur).

14.4.11

STOP CONDITION TIMING

A STOP bit is asserted on the SDA pin at the end of a

receive/transmit by setting the STOP sequence enable

bit, PEN (SSPCON2<2>). At the end of a receive/trans-

mit, the SCL line is held low after the falling edge of the

ninth clock. When the PEN bit is set, the master will

assert the SDA line low. When the SDA line is sampled

low, the baud rate generator is reloaded and counts

down to 0. When the baud rate generator times out, the

SCL pin will be brought high, and one TBRG (baud rate

generator rollover count) later, the SDA pin will be

de-asserted. When the SDA pin is sampled high while

SCL is high, the P bit (SSPSTAT<4>) is set. A TBRG

later, the PEN bit is cleared and the SSPIF bit is set

(Figure 14-21).

14.4.11.1

WCOL Status Flag

If the user writes the SSPBUF when a STOP sequence

is in progress, then the WCOL bit is set and the con-

tents of the buffer are unchanged (the write doesn’t

occur).

FIGURE 14-20:

ACKNOWLEDGE SEQUENCE WAVEFORM

Note: TBRG = one baud rate generator period.

SDA

SCL

Set SSPIF at the end

Acknowledge sequence starts here,

Write to SSPCON2

ACKEN automatically cleared

Cleared in

TBRG

of receive

ACK

ACKEN = 1, ACKDT = 0

SSPIF

software

Set SSPIF at the end

of Acknowledge sequence

Cleared in

software

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式